uxcell Foam Tubing for Handle Grip Support, Pipe Insulation, 20mm ID 30mm OD 1m Length Black

Worked great for replacement on stroller. Better than the original. A little wd40 and slid right on. Dried nice and tight. Be sure to measure your inner diameter.

These puppies work better than the name brand foam grip covers. The long piece will last you for years. Use scissors to cut, a compressed air blow gun to install it, just pinch the outside end of the foam over the compressor tip, inflate with air and slide them on.My FLHTK has heated grips and the heat comes through just fine. The foam has more of a smooth surface than name brand covers and doesn't absorb water in the rain like they do.I can't think of any cons.

I bought this to replace the foam tubing on the handle of my spa cover lifter. The original foam tubing had rotted and was falling out. Lift manufacture did not sell replacement and had no suggestions for a replacement, so I went looking for something and found this product. The 1 meter length is long enough for me to make two sets of replacements. Product was easy to cut and install. So far holding up extremely well so I could not be happier. If you are using a long piece more than 6" installation is made easier if you get the inside of the tubing wet. I just put it under the faucet and let water run through the center. With the tubing wet, it will slide over the bar or handle much easier. After the tubing dries, it will stick to the bar and not move. This of course assumes you by the tubing with an inner diameter equivalent to the bar or handle that you are installing it on.I showed this to the spa dealer I bought my tub from, and they immediately bought this product to sell to their customers. They were impressed with quality and how well it worked.

the rubber is a little soft and will deform after awhile. I'm using them for a pullup bar so they are taking pretty much weight but holding up OK

Exactly what I need, at a very reasonable price. Remove old grip, spray tube and inside new grip with a little soapy water and slide into place. After the water dries, grip is as good as new.

This tubing insulation is just what I needed to give new life to my tripod. The foam pipe insulation I had around it before was starting to disintegrate and was looking shabby. This foam tubing isn't like the foam insulation for water pipes. It's more like neoprene material, except without the outer fabric layer. It really does insulate (more on that later) and provides a nice grippy surface to hold onto. The only problem is the way it is folded, presumably for shipping.The tubing was shipped in a plastic envelope and was folded twice leaving three creases. These creases are permanent and unsightly. It ruins an otherwise beautiful covering. I tried using the same methods of removing creases from neoprene—pouring boiling water over the creases and inside the tube. Even with boiling water inside the tube, I could comfortably hold the outside of the tube, verifying the insulation performance. While the boiling water relaxed some of the smaller creases, the deep creases stayed. Even after letting it sit for 24 hours, the creases remain.A note on installing. These tubes are bit snug to keep them in place. This tube's ID is 28mm. My tripod leg is 28.1mm. The tubing will stretch a little, maybe ±1mm. Carefully measure the round part where you plan to install this, preferably with calipers.To install them, DO NOT USE any sort of petroleum lubricant such as WD-40 or grease. The tubing will slip and not stay in place if you do. To help slide it onto whatever you're mounting this on, use 91% rubbing (isopropyl) alcohol. DO NOT USE ethyl alcohol. Clean the surface where it will go with the alcohol, then pour some inside the tube and swish it around. While it's still wet slip the tube onto the surface. The alcohol gives just enough lubrication to allow the tube to slip. If tube starts to stick, lift up an edge and pour a little bit more alcohol inside. The alcohol will eventually evaporate and the tubing will stick to the surface and stay in place.For the product, I give it 5-stars. For how they store and ship it, I give them 1-star, so overall, 3-stars.

Worked great for cushioning a handle made out of black iron pipe

I used it for my yard rake, and it has stuck to the rake stick and shrunken to the rake stick as if I hadn't just bought it for the cushion. Only in two days this piece of junk is garbage. Please don't waste your money.